Sponsored by

VGoodiez 420EDC
  • Welcome to VaporAsylum! Please take a moment to read our RULES and introduce yourself here.
  • Need help navigating the forum? Find out how to use our features here.
  • Did you know we have lots of smilies for you to use?

Vape The Pinky - an open-source DIY injector style thermal extraction device

Vitolo

Vaporist
Here is the build guide:

It works great!
Very well balanced, and precise on temperature.
It is very light in weight... so it must be securely set down to avoid the cord's weight pulling on it.
I use my Taroma at 650º...
I only need to set the Pinky at610º
Here's mine:
DSC07227.jpg
 
Here is the build guide:

It works great!
Very well balanced, and precise on temperature.
It is very light in weight... so it must be securely set down to avoid the cord's weight pulling on it.
I use my Taroma at 650º...
I only need to set the Pinky at610º
Here's mine:
View attachment 34270


This is for extraction, like rosin making?
 
This is for extraction, like rosin making?
Not rosin, for use like the B1,B2,Qaroma etc vapes where this is used as an air heater above your bud.
 
Not rosin, for use like the B1,B2,Qaroma etc vapes where this is used as an air heater above your bud.

Like an herborizer?
Sorry, all the tech is new to me as I have been living under a rock

Edit: ok I get it
The flower pot B1 and B2
Just a heated element over some flower using the draw from a bubbler, water pipe etc to create the vapor flow
Actually just a stripped down flower pot
Ill research the tech and catch up
Should be able to customize some shtuffff
 
Last edited:
Yes @Tincandtoke ... @LesPlenty has it exactly.
It has lightweight but precise temperature, and is an inexpensive alternative to FlowerPot etc. and other PID/coil controlled heat sources.
It's a heavy hitting way to medicate that has a particular following.
It's a varietal delivery system for me.
Some fans will use no other system.
The color change feature is very subtle on mine, because I use it at 610º.
It gets obvious closer to 650-700.
Like an herborizer?
Herborizer uses the same downstem heat above flower system.
A closer match would be FlowerPot.
Even closer still would be the ceramic Ceroma. (below)
DSC07164 (1).jpg

The opening on the Ti version and the Ceramic is for the coi to be encased and leads to the handle.
The beads are poured into an inner chamber- coils sits in there and gets locked in via screwtop (which has air holes for the flow).
 
Last edited:
Yes @Tincandtoke ... @LesPlenty has it exactly.
It has lightweight but precise temperature, and is an inexpensive alternative to FlowerPot etc. and other PID/coil controlled heat sources.
It's a heavy hitting way to medicate that has a particular following.
It's a varietal delivery system for me.
Some fans will use no other system.
The color change feature is very subtle on mine, because I use it at 610º.
It gets obvious closer to 650-700.

Herborizer uses the same downstem heat above flower system.
A closer match would be FlowerPot.
Even closer still would be the ceramic Ceroma. (below)
View attachment 34273
The opening on the Ti version and the Ceramic is for the coi to be encased and leads to the handle.
The beads are poured into an inner chamber- coils sits in there and gets locked in via screwtop (which has air holes for the flow).

Would something like this work with deep dish 25mm 710 coils?
 
Would something like this work with deep dish 25mm 710 coils?
Not with the deep dish style or 25mm
The pinky circumference is made to fit into a 20mm coil, which must be open at both ends.
61zOcQ1SQfL._AC_SL1500_.jpg

The coil you mention has two directions of coil... one around, and a spiral coil as a floor.
Untitled.jpg

The correct coil(with the red wire cover above) can be obtained for $25-$40 from different sellers, and can be gotten
for less if one is willing to shop DHGate or other Chinese mail order concerns..
 
So simple. I have a box of adapters and had quite a few of this one.
Cheap...easy to get... an 18mmM to 18mmF with a screen slapped in there!
Screen sits snugly with no weed passing the barrier thanks to that Saturn ring in the center.
Photo on 2-28-22 at 1.51 PM 2.09.50 PM.jpg
 
So simple. I have a box of adapters and had quite a few of this one.
Cheap...easy to get... an 18mmM to 18mmF with a screen slapped in there!
Screen sits snugly with no weed passing the barrier thanks to that Saturn ring in the center.
View attachment 34289

So I just need to find a 20mm open coil
Back to 710
Is there a universal PID or do they all have different pin configurations?

Looking for a way to vape my flower using coils
Thought about the flower pot or nebulizer
I saw the Ispire wand mentioned in Troys review
How would that work
 
Is there a universal PID or do they all have different pin configurations?
That's the thing!
The pin configuration must match the PID.
Those fans that use this method a great deal do know the differences.
My Flowerpot was placed with a patient... but I am aware that the FP pin configuration was different
I have a feeling that one when building a system of their own gets the PID first and then matches the pin configuration to it.
Discord and Reddit are full of these folks, but it's not always easy to get help without snide remarks toward those with less knowledge.
I am sure somebody here knows the deal, and I hope they will chime in and offer solid information!
EDIT:
Just read the last part....
The Ispire wand is a portable heat source, that accomodates a cup or pot to vape waxes, and concentrates.
I imagine there would be a way to use it, but remember... it is portable and small.
The container that would need to be heated would have to fit into 18mm or 14mm.
It must be open, and filled or solid to gather heat and transfer it.
The Ispire may not be up for that challenge. (it must heat up.. and also heat the "heat source"... or housing that will go into the herb bowl)
I am friends with a person that uses these systems with ease.
I am not sure about cross forum referencing and referral.. so hopefully within short order another member here will notice our interface and quandry and help.
 
Last edited:
That's the thing!
The pin configuration must match the PID.
Those fans that use this method a great deal do know the differences.
My Flowerpot was placed with a patient... but I am aware that the FP pin configuration was different
I have a feeling that one when building a system of their own gets the PID first and then matches the pin configuration to it.
Discord and Reddit are full of these folks, but it's not always easy to get help without snide remarks toward those with less knowledge.
I am sure somebody here knows the deal, and I hope they will chime in and offer solid information!
EDIT:
Just read the last part....
The Ispire wand is a portable heat source, that accomodates a cup or pot to vape waxes, and concentrates.
I imagine there would be a way to use it, but remember... it is portable and small.
The container that would need to be heated would have to fit into 18mm or 14mm.
It must be open, and filled or solid to gather heat and transfer it.
The Ispire may not be up for that challenge. (it must heat up.. and also heat the "heat source"... or housing that will go into the herb bowl)
I am friends with a person that uses these systems with ease.
I am not sure about cross forum referencing and referral.. so hopefully within short order another member here will notice our interface and quandry and help.

I was asking because another person on GC, Psychedelic Sam, was looking for a good way to vape flower
Was not happy with the results of the wand
Assuming he is using a dynavap or something similar
Its a tincture thread so this topic is way out of the thread content

The coil set up is for me
I have to find a 20mm open end coil first
Then match the pid
Lots of pids, not so many coils in stock
Everybody is wrecking them pulling em apart!

I'm an idiot so it is best I stay away from reddit and the like
I will figure out the coil

In the vape zone article I thought they mentioned the wand
Was curious if anything was done
 
This advice was given to me by a friend.
This is not my research or wording, but I trust the person as he is an aficionado:
It is wisest to buy both the PID and coil from the same place, as some do not match even though looks like they do.
*Everything that @VGOODIEZ sells matches, but his coils are Cannabis Hardware which he is unable to offer a discount.

*Cannabis Hardware SOC10 is a 5% discount.

*Vgoodiez GOODIEZ20 is a 20% discount on that controller from "Disorderly Conduct" (another makerr of PIDs).

* I was told that a place called Discount enail has the best package deal:




discountenails.com


This is an excellent budget kit if you already have your own accessories. The PID E-Nail controller box controls the hot runner heating coil. The coil will heat from room temperature to 710 Degrees in about 3 minutes. This is the cheapest, best quality E-Nail controller on the market.
Looks like about $100 for the set.

*High Five had a BOGO but looks like their 20mm is sold out. You might be able to write them to put in a back order?
Looks like PID plus Coil for $160 which comes out to $80 each for the pair.

I've heard of a lot of people messing up their coil or PID bc it doesn't match. IT is possible to open up the coil and reconfigure, but thing easier to just buy the PID and COIL from the same place.
 
Nozzles:

Shit!
I saw welding and panicked
Been some time and I know just enough to kill myself
IMG_20220301_194851.jpgIMG_20220301_194909.jpgIMG_20220301_194922.jpgIMG_20220301_194936.jpg

This was going to be my first DIY coil project
Using the Titanium head from my Ditanium set up
I was going to buy some open end coils and stretch them around the upper half
The ditanium does a good job with flower but it is a vertical piece that gets inserted horizontally
The flower shifts and can easily combust
Plus you cannot put much flower in because of the risk of combustion
This would allow the head to be packed with 2X to 3X the amount of flower

Disclaimer:Thought up while very stoned
Writer not responsible for any of the bad parts
 
I will have 2 nozzles coming to me in the mail.
This would leave only balls and screens to acquire.
I have my Pinky set up already.
I will share the 2 Pinky Nozzles with "Those that desire them".
I offer them freely, but would like the taker to pay postage.
That does not mean I will refuse the 1st 2 askers, if they can not pay the postage.
 
This looks like a great affordable diy ball/injector vape
There's quite a few in this arena now

I have not used anything anywhere as good as my ball/injector vape
They extract quicker and better than any other vape I have, I can't combust and the clouds produced are amazing

My feco is half as strong as it used be with any other vape at all
I used to get 2ml of feco per Oz of green turned into avb
The last batch I got 1ml per Oz !!!

I don't have a pinky but from all reports it hits hard and is cheaper than other options in the same genre

I truly believe these ball/injectors are the future of vaping
Simplicity is better than all the fancy tech they've been selling us for years it seems
 

Sponsored by

VGoodiez 420EDC
Back
Top